RFID HOME SECURITY USING RC522

MATERIALS REQUIRED
1.ARDUINO UNO
2.RC522 RFID READER
3.POTENSIOMETRE
4.SERVO
5.MALE TO FEMALE JUMPER WIRE
6.PASSIVE BUZZER
7.BREADBOARD
8.RFID KEYCHAIN
9.PICC CARD

CIRCUIT


















FIRST DOWNLOAD THE LIBRARY FROM-https://github.com/miguelbalboa/rfid



CODE


#include <Servo.h>//LIBRARY OF SERVO
#include <EEPROM.h>// EEPROM LIBRARY
#include <SPI.h>//SPI LIBRARY
#include <LiquidCrystal.h>
LiquidCrystal lcd(2, 3, 4, 5, 6, 7);//PINS THAT ARE CONNECTED TO LCD DISPLAY
#include <MFRC522.h> //LIBRARY OF RC522 READER
 /*
  * LCD RS pin to digital pin 2
 * LCD Enable pin to digital pin 3
 * LCD D4 pin to digital pin 4
 * LCD D5 pin to digital pin 5
 * LCD D6 pin to digital pin 6
 * LCD D7 pin to digital pin 7
 * LCD R/W pin to ground
 * LCD VSS pin to ground
 * LCD VCC pin to 5V
 * 10K resistor:
 * ends to +5V and ground
 * wiper to LCD VO pin (pin 3
\*
/*

 -----------------------------------------------------
 * Pin layout should be as follows:
 * Signal     Pin              Pin               Pin
 *            Arduino Uno      Arduino Mega      MFRC522 board
 * ------------------------------------------------------------
 * Reset      9                5                 RST
 * SPI SS     10               53                SDA
 * SPI MOSI   11               51                MOSI
 * SPI MISO   12               50                MISO
 * SPI SCK    13               52                SCK

 */


#define SS_PIN 10//DEFINING THE MOSI PIN ON RC522 READER
#define RST_PIN 9//DEFINING THE RESETPIN ON RC522 READER
MFRC522 mfrc522(SS_PIN, RST_PIN); //RC522 INSTANCE
unsigned long uidDec, uidDecTemp;
// **************************************************************


unsigned long CardUIDeEPROMread[] = {
  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,
  30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49};

int ARRAYindexUIDcard;
int EEPROMstartAddr;
// -----------------------------
long adminID = 3230172949;
Servo lock;          
int pos=0;//THE START POSITION OF SERVO
void setup(){
   Serial.begin(9600);//OPEN SERIAL COMMUNICATION AT 9600BPS
   lcd.begin(16, 2);//BEGINING THE COMMUNICATION OF LCD DISPLAY
   lock.attach(14);//PIN THAT IS CONNECTED TO SERVO(A1)
   SPI.begin();//BEGINING SPI
   mfrc522.PCD_Init(); //INTIALISING RC522
   lock.write(pos);
   noTone(15);//TONE OF THE BUZZER
 
}

void loop() {
  lcd.print("  put your card  "),lcd.setCursor(0,1),lcd.print("  on the reader");//STARTING TEXT ON THE DISPLAY
  if ( ! mfrc522.PICC_IsNewCardPresent()) //CHEKING IF THERE IS A NEW CARD
  {
    return;
  }


  if ( ! mfrc522.PICC_ReadCardSerial())//READING THE CARD
{
    return;
  }


  for (byte i = 0; i < mfrc522.uid.size; i++)
  {
    uidDecTemp = mfrc522.uid.uidByte[i];
    uidDec = uidDec*256+uidDecTemp;
 
  }




  if (uidDec == 3230172949/*THE UID OF THE MASTER CARD IN DEC UNIT*/)//CHECKING IF THE THE CARD ON THE READER IS MASTER CARD
  {
     lcd.clear();//CLEARING THE LCD
    lcd.print(" Access granted");
    delay(1000);
    lcd.clear();
 
     for (pos = 0; pos <= 180; pos += 1) { // goes from 0 degrees to 180 degrees
    // in steps of 1 degree
    lock.write(pos);
    delay(15);
 
     }
     delay(10000);
     for (pos = 180; pos >= 0; pos -= 1) {
      delay(15);// goes from 0 degrees to 180 degrees
    // in steps of 1 degree
    lock.write(pos);
     }                                  

 
 
 


  }else{
      lcd.clear();
      lcd.print("Access denied");
      delay(1000);
      lcd.clear();
      lcd.print("ID:"),lcd.print(uidDec);
      delay(1000);
      lcd.clear();
      tone(15, 3520, 500);//TONE OF THE BUZZER
      }



    }
 
 

// ******************************************
// ******************************************

ADD FILE
#define NOTE_B0  31
#define NOTE_C1  33
#define NOTE_CS1 35
#define NOTE_D1  37
#define NOTE_DS1 39
#define NOTE_E1  41
#define NOTE_F1  44
#define NOTE_FS1 46
#define NOTE_G1  49
#define NOTE_GS1 52
#define NOTE_A1  55
#define NOTE_AS1 58
#define NOTE_B1  62
#define NOTE_C2  65
#define NOTE_CS2 69
#define NOTE_D2  73
#define NOTE_DS2 78
#define NOTE_E2  82
#define NOTE_F2  87
#define NOTE_FS2 93
#define NOTE_G2  98
#define NOTE_GS2 104
#define NOTE_A2  110
#define NOTE_AS2 117
#define NOTE_B2  123
#define NOTE_C3  131
#define NOTE_CS3 139
#define NOTE_D3  147
#define NOTE_DS3 156
#define NOTE_E3  165
#define NOTE_F3  175
#define NOTE_FS3 185
#define NOTE_G3  196
#define NOTE_GS3 208
#define NOTE_A3  220
#define NOTE_AS3 233
#define NOTE_B3  247
#define NOTE_C4  262
#define NOTE_CS4 277
#define NOTE_D4  294
#define NOTE_DS4 311
#define NOTE_E4  330
#define NOTE_F4  349
#define NOTE_FS4 370
#define NOTE_G4  392
#define NOTE_GS4 415
#define NOTE_A4  440
#define NOTE_AS4 466
#define NOTE_B4  494
#define NOTE_C5  523
#define NOTE_CS5 554
#define NOTE_D5  587
#define NOTE_DS5 622
#define NOTE_E5  659
#define NOTE_F5  698
#define NOTE_FS5 740
#define NOTE_G5  784
#define NOTE_GS5 831
#define NOTE_A5  880
#define NOTE_AS5 932
#define NOTE_B5  988
#define NOTE_C6  1047
#define NOTE_CS6 1109
#define NOTE_D6  1175
#define NOTE_DS6 1245
#define NOTE_E6  1319
#define NOTE_F6  1397
#define NOTE_FS6 1480
#define NOTE_G6  1568
#define NOTE_GS6 1661
#define NOTE_A6  1760
#define NOTE_AS6 1865
#define NOTE_B6  1976
#define NOTE_C7  2093
#define NOTE_CS7 2217
#define NOTE_D7  2349
#define NOTE_DS7 2489
#define NOTE_E7  2637
#define NOTE_F7  2794
#define NOTE_FS7 2960
#define NOTE_G7  3136
#define NOTE_GS7 3322
#define NOTE_A7  3520
#define NOTE_AS7 3729
#define NOTE_B7  3951
#define NOTE_C8  4186
#define NOTE_CS8 4435
#define NOTE_D8  4699
#define NOTE_DS8 4978